How To Change Front Brake Pads On A Harley Road King?

Harley-Davidson motorcycles are well known for their quality and durability. However, even the best made machines will eventually need maintenance and repair. One common repair is changing the front brake pads on a Harley Road King. This is not a difficult task, but it does require some basic mechanical skills. Here is a step-by-step guide to changing the front brake pads on a Harley Road King.

  • Park the bike on a level surface and set the parking brake
  • Remove the wheel by loosening the axle nuts with a wrench
  • Take out the old brake pads and clean up any rust or debris from the caliper with a wire brush
  • Place the new brake pads in, making sure they are properly aligned in the caliper
  • Put the wheel back on and tighten down the axle nuts until they are snug but not too tight – you don’t want to strip them
  • Test ride your bike around the block to make sure everything is working properly before heading out on the open road!
How To Change Front Brake Pads On A Harley Road King?

How Often Do I Need to Change My Front Brake Pads on My Harley Road King

Harley-Davidson recommends changing your front brake pads every 20,000 miles. However, depending on how often you ride and how hard you ride, you may need to change them sooner. If you notice that your brakes are starting to feel less responsive or if they are making noise when you apply them, it’s time for new pads.

What are the Consequences of Not Changing My Front Brake Pads

If you don’t change your front brake pads, the consequences can be pretty serious. Your brakes will gradually become less effective, and eventually, they may fail entirely. This could lead to an accident, and potentially serious injuries or even death. It’s important to keep an eye on your brake pads and replace them when necessary. If you’re not sure how often to do this, consult a professional mechanic.

They’ll be able to tell you how often to change your brake pads based on your driving habits and the wear and tear on your brakes.

How Do I Know When It’s Time to Change My Front Brake Pads

If your car has front disc brakes, you’ll know it’s time to change the brake pads when you hear a high-pitched squeal coming from the wheels when you brake. The squeal is caused by a metal tab on the brake pad that rubs against the rotor to let you know that the pads are wearing thin and need to be replaced.

You may also notice that your car takes longer to stop than usual, or that the pedal feels “soft” when you press down on it. These are both signs that your brake pads need to be changed. If you’re not sure whether or not your car has front disc brakes, consult the owner’s manual or ask a mechanic.

Where Can I Get New Front Brake Pads for My Harley Road King

If you’re in need of new front brake pads for your Harley Road King, we’ve got you covered. We’ll go over where to find the right set of brake pads for your bike, and what to look for to ensure they’re a perfect fit.

When it comes to finding new front brake pads for your Harley Road King, there are a few different places you can look. Your local motorcycle parts store is always a good place to start. However, if you want to be sure you’re getting the best possible deal on your new pads, we recommend shopping around online.

There are a few things you’ll need to know before ordering new front brake pads for your Harley Road King. First, you’ll need to know the model and year of your bike. This information can usually be found on the VIN (vehicle identification number) plate located on the frame of your bike.

Once you have this information handy, simply enter it into our online fitment guide and we’ll show you all the compatible options for your ride. Once you’ve found the perfect set of brake pads for your Harley Road King, be sure to double-check that they’re compatible with your bike’s rotor size and caliper type.

With that taken care of, simply follow our easy-to-use installation instructions and enjoy increased stopping power and improved braking performance from your newly installed brakes!

How Do I Install New Front Brake Pads on My Harley Road King

Harley-Davidson’s Road King is a big bike, and it needs big brakes to rein it in. The front brake calipers each have two pistons, so you’ll need to install new pads on both sides when they wear out. Here’s how to do it:

1. Jack up the front end of the bike and remove the wheels. This will give you access to the brake calipers.

 2. Unbolt the caliper mounting bracket from the fork leg using an Allen wrench or socket wrench. Be careful not to lose any of the small parts that may fall out when you remove the bracket (e.g., washers, spacers).

 3. Pull the old brake pads out of their slots in the caliper halves. If they’re stuck, use a flat-head screwdriver to pry them loose. Be careful not to damage the piston or bore of the caliper while doing this.

 4. If your new pads come with anti-squeal shims: Install them onto each pad according to the manufacturer’s instructions, then insert each pad into its slot in each caliper half (one at a time). Make sure that they’re fully seated and aligned properly before moving on to step 4b below. b) If your new pads don’t come with anti-squeal shims: Insert each pad into its slot in each caliper half (one at a time), making sure that they’re fully seated and aligned properly before moving on to step 5 below.)

5) Reinstall the caliper mounting bracket(s), being careful not to cross-thread any of the bolts, and torque them to spec according to your service manual (typically 20-30 ft.-lbs.). 6) Repeat steps 1-5 for the other side/caliper if necessary, then reinstall your wheels and lower your bike off the jack stands or lift.

Harley-Davidson Brake Pad Replacement

If your Harley-Davidson is due for a brake pad replacement, you’re in luck. This is a relatively easy job that you can do yourself with just a few tools.

Here’s what you’ll need to get the job done: -Socket wrench -Torque wrench -Brake pads (new)-Lubricant (optional) First, remove the wheel from your Harley. You’ll need to loosen the axle nut with the socket wrench, then remove the caliper bolts with the same tool. Once the caliper is loose, remove the old brake pads and replace them with new ones. Be sure to use lubricant on the new pads if desired.

Finally, use the torque wrench to tighten everything back up according to manufacturer specifications. And that’s it! You’ve now successfully replaced your Harley’s brake pads. Enjoy hitting the open road knowing that your brakes are fresh and ready to go.

Harley Davidson Front Brake Caliper Removal

Harley Davidson Front Brake Caliper Removal: Removing the front brake calipers on a Harley Davidson motorcycle is a relatively easy task that can be completed in just a few minutes. The most important thing to remember when removing the calipers is to support them securely so that they do not fall and damage the brake lines.

With the calipers supported, simply remove the bolts that hold them in place and then slide them off of the brake rotor.

How to Change Front Brake Pads on 2013 Street Glide

It’s important to keep your brakes in good working order, and that means changing your brake pads when they start to wear down. If you have a 2013 Street Glide, here’s how to change your front brake pads.

First, you’ll need to remove the old brake pads. To do this, first, loosen the two screws that hold the caliper in place. Then, use a flathead screwdriver to pry the old pads out of the caliper.

Once they’re out, you can inspect them for wear and tear. Next, it’s time to install the new brake pads. Start by lining up the new pads with the caliper so that they fit snugly into place.

Once they’re in position, tighten down the two screws to secure them in place. Finally, bleed your brakes according to manufacturer instructions before taking your Street Glide out for a spin!


If you own a Harley Road King, sooner or later you’re going to have to change the front brake pads. It’s not a difficult task, but there are a few things you need to know before you get started.

First, you’ll need to remove the caliper from the fork. This is done by removing the two bolts that hold it in place. Once the caliper is off, you can remove the old brake pads and install the new ones. Be sure to check the thickness of the new pads before installing them – they should be identical to the old ones.

Once the new pads are in place, reinstall the caliper and tighten down the bolts. You may need to bleed the brakes after this, so consult your owner’s manual for instructions on how to do that.

Alston Seymour

A Harley-Davidson Motor Company certified Master Technician and avid biker, I love to write about everything and anything related to biking.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: