How To Change Rear Brake Pads On Harley Softail?

If you’re like most Harley riders, you probably don’t do a lot of your own maintenance. But changing your rear brake pads is a relatively easy job that anyone can do with a little time and the right tools. Here’s how to change rear brake pads on a Harley Softail.

  • Park your motorcycle on a level surface and engage the parking brake
  • Remove the wheels from your motorcycle
  • Unbolt the caliper using a wrench or socket set and pull it away from the rotor
  • Take out the old brake pads and insert new ones, being careful to avoid damaging the caliper pistons
  • Reattach the caliper and bolt it in place, then replace the wheels on your motorcycle
How To Change Rear Brake Pads On Harley Softail?

Is It Ok to Just Change the Rear Brake Pads?

It is not advisable to just change the rear brake pads. Doing so would create an imbalance in the braking system, with the front brakes doing most of the work. This could lead to premature wear on the front brakes and decreased overall braking performance. It is best to change both front and rear brake pads at the same time to maintain balance and optimal performance.

How Often Should Brake Pads Be Changed on a Harley Davidson?

It is generally recommended that brake pads be changed every 20,000 miles on a Harley Davidson. However, it is important to check the condition of your brake pads regularly and replace them when necessary. If you notice any unusual wear or tear on your brake pads, it is best to replace them as soon as possible.

Can You Replace Rear Brakes by Yourself?

You can absolutely replace your rear brakes by yourself! The process is pretty straightforward and doesn’t require any special tools or knowledge. Here’s a quick rundown of what you’ll need to do:

1. Jack up your car and remove the wheels.

2. Remove the old brake pads and discs (if they’re not already detached).

3. Attach the new brake pads to the caliper. Make sure they’re properly aligned!

4. Reattach the caliper to the rotor/wheel assembly. Again, make sure everything is lined up correctly.

5. Put the wheels back on and lower your car down from the jack stands.

Can You Replace Bike Brake Pads Without Removing the Wheel?

It is possible to replace bike brake pads without removing the wheel, but it is not always the easiest or most effective method. To do this, you will need to loosen the bolts that hold the pad in place, and then carefully pry the old pad out. You may need to use a small screwdriver or another tool to help with this.

Once the old pad is out, simply insert the new one and tighten the bolts back up. One potential issue with replacing brake pads without removing the wheel is that it can be difficult to get a good seal on the new pads if they are not perfectly aligned.

This can lead to decreased braking performance and increased wear on both the pads and rotor. Additionally, if your bike has disc brakes, it is important to make sure that the caliper is properly centered over the rotor before tightening everything back up; otherwise, you risk damaging your rotor.

As such, unless you are confident in your ability to replace brake pads without removing the wheel, it is generally best to leave this task to a professional mechanic.

Harley Davidson Rear Brake Pad Replacement

Harley Davidson Rear Brake Pad Replacement: If your Harley Davidson is in need of a rear brake pad replacement, don’t worry – it’s a relatively simple process that you can do yourself with just a few tools. Here’s a step-by-step guide to replacing your Harley’s rear brake pads:

1. First, lift the bike up onto its stand so that you can easily access the rear wheel. Remove the wheel by loosening the axle nuts with a wrench.

2. Once the wheel is removed, you’ll be able to see the brake caliper – this is what houses the brake pads. Use a wrench to remove the two bolts that hold the caliper in place, and then carefully remove it from around the disc (taking care not to damage anything).

 3. With the caliper removed, you should now be able to see the old brake pads clearly. Simply pull them out and discard them – they’ll need to be replaced with new ones.

4. To install the new brake pads, simply reverse the process above – fit them into place in the caliper and then bolt everything back together again (being sure not to over-tighten any of the bolts). Finally, replace your wheel and lower your bike back down off its stand.

Harley Davidson Rear Brake Caliper Removal

Harley-Davidson rear brake caliper removal is a pretty easy process, but there are a few things you need to know before you get started.

First, you’ll need to remove the wheel and then the caliper itself. To do this, start by removing the two bolts that hold the caliper in place.

Once these are removed, you can simply pull the caliper off of the mounting bracket. Now that the caliper is free, you can access the brake pads. There are usually two screws holding each pad in place.

Remove these screws and then gently pry the pads out of the caliper. Be careful not to damage any of the other components while doing this. Once the pads are out, take a look at them to see if they need to be replaced. If they’re excessively worn or damaged, it’s best to replace them with new ones.

Otherwise, just clean them up and re-install them following the same steps in reverse order. With fresh brake pads in place, your Harley-Davidson will have better braking power than ever before!

How Do You Change the Brake Pads on a Harley Softail

If you own a Harley Softail, at some point you’re going to need to change the brake pads. It’s not a difficult job, but there are a few things you need to know before you get started. First, you’ll need to purchase the correct brake pads for your bike.

There are different types of pads available, so make sure you get the right ones. You can usually find this information in the owner’s manual or on the manufacturer’s website. Once you have the correct pads, follow these steps to change them:

1. Remove the old pads by unscrewing the retaining clip and sliding them out of place. Be careful not to damage the caliper in the process.

2. Clean any debris from the caliper with a rag or brush.

3. Place the new pads into position and screw the retaining clip back in place. Make sure they’re securely in place before moving on.


In order to change the rear brake pads on a Harley Softail, you will need to first remove the wheel. Once the wheel is removed, you will be able to access the brake caliper. The brake caliper houses the brake pads.

To remove the old brake pads, simply squeeze the caliper together and pull out the old pads. Insert the new pads into place and reassemble everything.

Alston Seymour

A Harley-Davidson Motor Company certified Master Technician and avid biker, I love to write about everything and anything related to biking.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: