How To Change Hand Grips On Harley?

There are a few different ways to change hand grips on a Harley. The most common way is to simply unscrew the old grip and screw on a new one.

This can be done by hand, but it is often easier to use a wrench or socket set. Another way to change hand grips is to slide the old grip off and then slide the new grip onto the handlebar. This can be tricky, as you need to make sure that the new grip is lined up correctly before you push it onto the handlebar.

  • Park your Harley on a level surface and turn off the engine
  • Lift the seat to access the battery
  • Disconnect the negative cable from the battery using a wrench
  • Remove the bolts that hold the hand grips in place using a Phillips head screwdriver
  • Pull the old hand grips off of the handlebars
  • Slide new hand grips onto the handlebars and tighten the bolts with a Phillips head screwdriver to secure them in place
  • 7 Reconnect the negative cable to the battery using a wrench
How To Change Hand Grips On Harley?

How Do You Put Handlebar Grips on a Harley?

If you’re looking to add some new handlebar grips to your Harley, there are a few things you need to know.

First, you’ll need to decide what kind of grips you want. There are many different styles and materials available, so take some time to look at all your options and pick the ones that best suit your needs. Once you have your new grips, it’s time to install them. Here’s a quick guide on how to do just that:

1. Start by removing the old grips from your handlebars. This can be done by heating them up with a hair dryer or heat gun until they become soft enough to slide off. Alternatively, you can use grip adhesive remover (available at most auto parts stores).

2. Clean the inside of the handlebars thoroughly with alcohol or another solvent; this will help the new grips adhere better.

3. Place the end of one grip onto the handlebar, then start working it on from one end towards the other. If needed, use a small amount of grip adhesive or hairspray to help keep it in place as you go along. Repeat with the other grip.

4. That’s it!

How Do You Replace Motorcycle Hand Grips?

Assuming you would like tips on how to replace motorcycle hand grips: Tools you will need are: Flathead screwdriver, Phillips head screwdriver, razor blade, or box cutter. Here are the steps:

1. Remove the old hand grip by unscrewing any screws that may be holding it in place with a flathead or Phillips head screwdriver. You may also need to use a razor blade or box cutter to loosen the grip from the handlebar.

2. Clean off any dirt, debris, or old adhesive from both the handlebar and the inside of the new hand grip with a rag soaked in rubbing alcohol. This will help ensure that the new grip will adhere properly.

3. If your new hand grips come with adhesive backing, simply peel off the paper backing and press the grips onto the handlebars. Start at one end and work your way towards the other, making sure that they are aligned correctly as you go.

If there is no adhesive backing, apply a thin layer of glue around the circumference of each handlebar before pressing on the new grips firmly until they are in place.

How Do You Replace Hand Grips?

Assuming you would like tips on how to replace handlebar grips: The tools needed: are an Allen key or screwdriver, grip adhesive, and new grips.

1. Remove the old grips by loosening the screws at the end of each grip and then sliding it off the handlebar. If your bike doesn’t have screws, you may be able to peel the old grip off.

2. Clean up the handlebars with rubbing alcohol or another solvent to remove any residue from the old grips and prepare them for the new ones. Let them dry completely.

3. Apply a layer of adhesive to one end of each new grip then slide it onto the handlebar until it’s in the correct position. Repeat with the other grip.

4. Tighten the screws at each end of the grip or wait for the adhesive to set according to its instructions before riding again.

How Do You Get Harley Grips to Stick?

Harley grips are made of a soft, pliable material that can be easily damaged. The best way to get them to stick is to use a good-quality adhesive.

There are many adhesives on the market that claim to be the best for this purpose, but we have found that the 3M Super 77 Multipurpose Adhesive works well. It is important to follow the directions on the adhesive packaging carefully in order to get the best results.

How to Replace Motorcycle Grips on a Cruiser

Most cruiser motorcycles come with stock grips that are made of hard plastic. Over time, these grips can become worn and uncomfortable. Luckily, they’re easy to replace. Here’s how:

1. Start by removing the old grips. Use a sharp knife or razor blade to carefully cut through the grip material. Work slowly and be careful not to damage the handlebars underneath.

2. Once the old grips are removed, clean the handlebars with rubbing alcohol to remove any residue.

3. To install the new grips, simply slip them over the handlebars and align them how you want them positioned. Once they’re in place, use a few drops of super glue or another adhesive to secure them in place. Allow the adhesive to dry completely before using your motorcycle again. That’s all there is to it!

How to Change Grips on a Motorcycle

If you’re like most motorcycle riders, you probably don’t think much about your grips. But if they start to wear out or slip, it can be a big problem.

Fortunately, changing motorcycle grips is a relatively easy task that anyone can do with the right tools and a little bit of know-how. Here’s a step-by-step guide to changing motorcycle grips:

1. Start by removing the old grips. This can be done with a screwdriver or other sharp tool. Just insert the tip of the tool under the grip and pry it off. Be careful not to damage the handlebars in the process.

2. Once the old grip is removed, clean off any residue from the handlebar using alcohol or another solvent. This will help ensure that the new grip adheres properly.

3. Next, apply some adhesive to the inside of the new grip (this step is optional but recommended). Then slide the grip onto the handlebar until it’s in position.

4. Finally, use a hairdryer or heat gun to lightly warm up the outside of the new grip.

Harley Davidson Hand Grips

Harley Davidson hand grips are an important part of the motorcycle. They provide comfort and style while you’re riding. There are many different types of hand grips available, so it’s important to choose the right ones for your motorcycle.

Here’s a look at some of the most popular options: – OEM Harley Davidson Hand Grips: These are the original hand grips that come with your motorcycle. They’re made from high-quality materials and offer a great grip.

If you’re looking for something that’s durable and looks great, OEM hand grips are a good option. – Aftermarket Harley Davidson Hand Grips: There are many aftermarket companies that make hand grips for Harley Davidson motorcycles.

These companies use different materials and designs, so you can find hand grips that suit your style. Aftermarket hand grips usually cost less than OEM ones, so they’re a good option if you’re on a budget. – Custom Harley Davidson Hand Grips: If you want something unique, you can get custom hand grips made for your motorcycle. You can choose the material, design, color, and more when you order custom hand grips.

This is a great way to add your own personal touch to your bike.


Harley-Davidson motorcycles are well known for their customization options, and one of the most popular ways to customize a Harley is to change the hand grips.

There are a few different ways to go about changing hand grips on a Harley, and the best method will vary depending on the model of motorcycle you have.

In general, however, changing hand grips on a Harley is relatively simple and can be done in just a few minutes with basic tools.

Alston Seymour

A Harley-Davidson Motor Company certified Master Technician and avid biker, I love to write about everything and anything related to biking.

Click Here to Leave a Comment Below 0 comments

Leave a Reply: